Welcome to my Robin Blog.

It was suggested to me that I start a Blog on my ultralight project the "Robin". I have been working on this project for 4 years. On one of my first days at Vought aircraft, a stress man and future friend named Kenny Andersen walked up to me and said, "Aren't you the Mark Calder that designed the Wren Ultralight" Why yes I am I said. "well what have you done lately?" That was the genesis of the Robin design. The first 2.5 have been spent in the design phase. Actual construction started 1.5 years ago and has actually progressed smoothly. There have been a number of changes from the onset, but for the most part it is following my original concept. I will eventually sell plans for the Robin and make available all molded parts, fittings and welded assemblies. The Robin is designed to FAA part 103 and as such requires no pilots license to fly, although I think its a good idea to actually learn how to fly!! The actual name "Robin" was my Daughter Jamie's idea, I asked her to name the design based on my "cute little bird" theme (Wren)



Every good aircraft design has a "Mission" in mind before the actual design is started. A good designer will refer back to this mission every time a design decision must be made. Good design after all is just a series of good design decisions. On my first Ultralight design the Wren, the mission was to design a high performance low powered aircraft. The reduction of drag was the prime concern. I had been flying powered Hang gliders prior to this and because of this experience, I placed a high priority on climb performance. While most designers chose bigger engines, I chose lower drag and high aspect ratio (low span loading) wings. The Wren could out climb conventional Ultralight with up to 65 hp. The Robin follows this philosophy, but tries to improve on the performance of the Wren. Ultralight are not built by "rich" people, they offer an inexpensive means to enjoy one of the greatest experiences of my life, low speed soaring and flying.



Design Concept



The cost of an aircraft is directly proportional to its weight. , if low drag can be achieved then lighter and cheaper engines can be used. The Robin expands on the design mission of the Wren by using a longer span (40') wing and using a low speed laminar flow airfoil, (Wortmann FX 170) The leading edge of the wing on the prototype is molded fiber glass. The spar has been placed at 33% of the wing chord because the chosen airfoil is laminar over the first 32%. The aft covering is light weight Dacron Fabric. The leading edge of this fabric is purposely pinked and placed at the 32% chord point to facilitate laminar transition and elimination of separation bubbles. The main difference between the original design of the Robin and the current final design is the elimination of the single mono wheel retractable landing gear. Part 103 does not allow for a retractable landing gear. Which is really unfortunate because I spent a long time designing a really neat mechanism!!

In the course of the 4 years I have worked on the Robin, the structural design concept has evolved radically. Originally I was going to draw on the design of the Wren and use essential the same construction concepts. The original design of the Wren was heavily influenced by my Friend Steve Wood's Sky Pup design. I lived in Wichita Kansas and worked at Cessna Aircraft along with Steve. I watched his progress on the Pup and was very impressed with his concepts. I adapted the concept of using Styrofoam sheeting as the shear panels for the fuselage and the wing ribs. I did not however use the foam for the shear webs of the wing as Steve did. I originally wanted to build the fuselage of the Robin in a similar manner. Weight and the desire to not use foam for the basic structure due to the danger of fuel leaking eventually drove me to a all wood fuselage design. The wings were designed to take advantage of the Graphlite carbon pultruded material pioneered for the experimental aircraft by Jim Marske. I was familiar with this product from my experience at Bell Helicopter where it was considered in the construction of the V-22 wing.









Latest Update

Update

 

I am sorry its been so long since Ihave done an update to the Blog. Events have conspired that demanded all of my time. I had to take an emergency leave from work to help my mother who unfortunatly was diagnosed with terminal cancer. I could write for weeks on the ins and outs of Hospice care!! My Mother unfortunatly passed away after 4 weeks. At least she wasn' in any pain thanks to the Angels in Nurses uniforms who work for Hospice at Henry Ford Hospital!! 

my poor old ma, God rest her soul!
This is a hoot!! This is a picture of my Ma 3 years ago at Halloween dressed as Jimmy Leyland the current Detroit Tigers manager, my ma was a huge Tigers fan and during the Funeral, the organist actually played "Take me out to the Ball Park" when we were walking her casket out of the church. She wouldn't have had it any other way!!! 















When I got back to Texas, I recieved notification of shipment of my new Router. That took a good two weeks of my time dealing with the shipping agents, customs and secondary shippers. But it was definitly worth it!!  I took a bit of a risk by ordering this router from China. I have had some quality problems, but thankfully all of the important stuff like Bearings, gears and servos came from Tiawan and Japan. My biggest issue turned out to be poor Chinese quality control on the wiring. Servo motors are very sensitive to noise and because of this they require good grounds and solid connections. The latter was the root of my early problems. I ended up soldering every crimped connection on the machine.
The proud owner and his new Router

The router is 4' x 8' x 19" it has a variable speed 7.35 hp spindle. I can machine wood, aluminum, plastic and steel with this. It took a while to get this up and running, but thanks to my Buddy Ed who is an electronics genius, we worked out all of the initial bugs. I plan on using the router for fabrication of a all wood airplane kits. On the side we are also using it to cut some beautiful laminated wood gun stocks. Here is a picture of a couple of test projects we cut using standard clip art from our 3d software files.

Cat and the Eagle
These projects were roughed out with a 1/4" ball nose cutter. after the rough cut the finish cut was done with a 1/16" ball nose cutter. The router took a pass every .007" Each piece took 1 hours to finish cut.


















Back to the Robin!!!

I decided to swap out engines. The MZ 34 proved itsself to be an unreliable choice. The engine just would not cool. The vibration is terrible and because of the earlier problem of it dieseling and not shutting off, I decided it was unsafe. When I went to the SSA Western homebuilding convention in Tehachapi Ca, I was talked into swapping the engine for a Briggs and Stratton Vanguard V twin. I am in the process of adding that engine. Unfortunatly I am forced to leave the cylinders unfaired and in the breeze just like other aircraft that use the same engine. This in my opinion detracts greatly from the original lines of the Robin which was designed to emulate the Fournier RF4D. Consequently, I am drawing all of the final plans using a 1/2 VW or a modified Generac industrial engine. Both of these engine are opposed Boxer configurations.
 The first thing I needed to do to use the Vanguard was to strengthen the fwd fuselage to accept the higher shear loads. I decided that the simplest method for the modification would be to sheet the fwd section with plywood. I had to double up the fwd longerons so I could bolt new fittings for the new engine.


side truss with doublers
  This is a view of the fwd fuselage side truss . I designed the original truss so close to the existing loads, that I had to double up all of the members between the landing gear and the firewall. Also you can see the large plate doublers added to the fwd longerons to accept the mount fittings. Unfortunatly this meant that I had to uncover the whole fuselage!! That is not a bad thing actually, because I had a number of areas that were not well thought out regarding the final shape after covering. This will give me a chance to clean all of that up.



side sheeting

After the doublers were addded, I then sheeted the sides with 1/16" Finnish Birch plywood. The circular cutout is for access to the brake pedal adjustment screws.










I am stripping the engine of a great deal of its weight, just the steel shrouding alone adds 5 lbs. The flywheel is 15 lbs! I have debated inverting the engine and making a new ignition , But since this is going to be a one off design I have decided to just turn the flywheel down and use the stock ignition. I am driving the prop from the flywheel side and mounting the engine on the PTO side.

PTO of Vanguard
On this engine I am again designing a dynafocal mount system. To refresh everyones memory, a dynafocal mount is designed to theoretically support the engine at the exact center of gravity. The theory is that all vibration nodes are zero crossing in there amplitude when they pass through the center of gravity. Since there is zero displacement at this point if it were possible to attach here, there would be no induced vibration into the mount. Obviously this is impossible so the next best thing to do is focus the input axis of the rubber shock mounts through the center of gravity. To find this angle a process called tri-filing is used.

Trifiling process


I made up some small lugs with a small hole in them. I attached a length of welding rod through that small hole and then hung the engine from that rod. I then took an angle measurement and that determined the input angle to the center of gravity. I then designed the mount to these angles. The picture above shows 4 angles lugs that the engine mounts attach to.


This brings everyone up to date with my progress.


Now forf the bad news, as I write this I'm sitting in the Admirals club at DFW airport waiting for a flight to Brazil!!! My company Triumph Vought just won a contract to design the aft section of the new EMB 195 airliner. Yours truly is in charge of the Empannage!! I will be at Embraer for 4 weeks starting tomorrow. To all of the Brazillian blog followers, if you are around Sao Jose Dos Compos, please write me at : Planebuilder@yahoo.com.

Mark

No comments: