Rudder Pedals and the Zimmer skimmer

I apologize for not making an update sooner, I’m at that phase of every project where the tiny details start to eat up the most time. A friend in Wichita once told me this is the phase where you are 90% complete with 90% left to do. My squawk list is getting huge. The number of “final” jobs range from ordering new bolts of the proper grip, to adding Fiberfrax to the firewall.

 In that regard I have completed the cowling and internal baffles for the engine. I am now ready to start routing electrical and throttle cables. But before I can do any of that, I needed to pull the engine and cover the firewall with a Ceramic blanket which will act as a fire wall. On top of the Fiberfrax surface, will be a coating of Latex Contego primer. This will serve to protect the Ceramic Paper (Fiberfrax) from contamination due to fuels and will also form a charred surface in the event of a fire. This will add precious minutes in the event of a engine fire.



New rudder Pedals



I started to install the new Rudder pedals and the new cable run. I am very happy with the final design here. But again, there are lessons that were learned that will be incorporated into the final plans. This is why you should never buy a set of plans that are all “paper” Building a prototype shows the mistakes and omissions a designer will make. Building a plane from plans that has never flown in my opinion is not only dangerous, but unethical on the designer’s part. One of the features I copied from the original RF4D was the canted rudder hinge line. I like the look and the fact that deflection of the rudder will induce a small rolling moment in the direction you are trying to turn in. That effect is minor, the main driver was styling. Well that angle leads to all sorts of problems when it comes to driving the rudder. The rudder horn is rotating in a canted plane that necessitates the redirection of the rudder cables. They need to be in the same plane as the rudder horn. On my design I further complicated this problem by mounting the rudder horn on the lower rudder rib, which is not perpendicular to the rudder hinge line. This means that the connection to the horn needs to articulate with two degrees of freedom. Too complicated!!!!  I have a solution for the prototype, but I will rectify this in the final design.

I am using Piper split cable guides to route the rudder cables. I have always liked these guides. In fact, we have swapped out the original oak wood guides in a 1-26 sailplane  I am helping my instructor rebuild. (I am getting some real tail dragger time right now in a Citabria) The beauty of these guides is that they are split and held together with a snap ring. When they are disassembled, the complete cable assembly can be removed, turnbuckles, thimbles and shackles. They are made from Nylon and as such offer a nice smooth friction free sliding surface. 

Rudder Cable bushings



This is the initial installation of the new Rudder Pedals. As usual, I forgot to add a “bow sprit” to the center body to attach the return springs to. This is being fixed. In fact, I just ordered some 6061-T6 Aluminum tubing because I want to replace the welded steel parts. My friend Ed has a nice TIG welder and claims he can weld me up a set. Just to make sure, I ordered 3 times as much as I should need. (sorry Ed!!) The rudders pedals can be swapped pretty easy and I will hold off terminating the cable that run fwd of the pedal “S” tubes. 

Zimmer Skimmer



This is a little off topic, but I thought you might find this interesting; this is a picture of the Zimmer Skimmer. This plane was conceived just prior to the start of WW II. It was envisioned as a carrier based fighter. It had an extremely short take off roll due to the twin almost helicopter like propellers. The Navy was actually interested in this plane and as a venture between Zimmer and my Company Vought Aircraft, two flying prototypes were built. The Skimmer was powered by twin C-85 engines driving the propellers through a 6.1 to 1 reduction gear box. Vought Aircraft actually started construction of a real fighter powered by two Allison V-12 engines. Both planes were ready for their first flight when the Navy cancelled the program and ordered both planes scrapped. This Plane is the last remaining example and is on loan from the Smithsonian Institute. The Vought Retirees club is undertaking a full restoration. This has been an ongoing project for the club for the last 6 years and it is now finally nearing completion. Notice in one of the Pictures the ducted fan attached to the C-85 sitting under the body.